Showing posts with label Hardware Repairs. Show all posts
Showing posts with label Hardware Repairs. Show all posts

Friday, May 29, 2009

Repairing the SATA slot on a HP Compaq 6710s laptop


About a month ago I found an ad for a HP 6710s, with a Core2Duo T7100 CPU, 2GB RAM and a 160GB hard drive, WiFi, BT, DVDRW LS, and a carrying bag. The seller mentioned that there was some kind of a problem with the hard drive slot, and sent me a photo of the problem (the image on the left is that original photo, I just added the red highlight circle).
I purchased this laptop for about $170.
The problem was that while inserting the hard drive, the previous owner broke off the plastic framing of the SATA connector, and also broke off one of the pins. This defect basically made the laptop useless as there is no way to make sure that the hard drive will align well with the exposed pins, and moreover, there was no way to know if the hard drive would actually work as one pin from the SATA slot was missing.


(Click on the images to view them in full size)

As you can see the pins from the image on the left, the SATA Connector pins are exposed, and one pin is broken. The pins originally were wrapped with a plastic shield that served both as a protector and as a rail that ensured correct alignment of the Hard drive’s connectors with the pins on the motherboard. This plastic housing also ensured that enough pressure is applied so that the hard drive’s pins have good connectivity with the pins on the motherboard. Without a functional SATA slot, there is no way to use the laptop.

So, we are facing two issues: the broken plastic shield, and the broken pin.
The broken plastic shield problem is not so difficult to solve. I used an acrylic based glue (a.k.a. Super glue) and glued back the torn off plastic wrapping. On the image on the right, you can see the aftermath of the operation, where the SATA connector is restored back to its original form. But before we get to the phase of the superglue and sticking back the plastic housing, we need to see what this missing pin actually does.
Since we’re dealing with a SATA slot, we should know a bit about it. Unlike the IDE/Parallel ATA slot, this technology creates a data stream i.e. a line of bits, therefore the name of SERIAL ATA. So all it takes for a SATA drive (in theory) is just one wire to transfer all the data, unlike the PATA that uses 40 pins interface. The SATA slot has two groups of pins: the smaller one that is the DATA part, and the larger one that is the POWER part. So, small group for data, big part for electricity.

Let’s now get back to the problem. As you can see, the missing pin is fourth from the top down (look at the red circle in the previous image on the left) on the Power group. Now let’s take a look at the hard drive’s connector and locate the matching pin to this missing one on the SATA connector.


(Click on the images to view them in full size)

Looking at the hard drive reveals the cause for the broken off pin. The image on the left indicates the matching pin on the hard drive with the missing pin’s position on the SATA connector, while the detail on the right points as to what damage was made on the hard drive’s plug when the pin from the SATA connector broke. The previous owner obviously pushed hard enough to break both the plastic shield and make this large dent on the hard drive socket itself. One hard push and he had to give up his laptop for a bargain price. But let’s move on.
In order to find out what this fourth pin does, I took the laptop’s hard drive and with a multimeter measured the resistance between the fourth pin and the surrounding pins. The interesting thing was that the fourth, fifth and sixth pins had zero resistance between each other. This means that this group of pins actually worked as a single pin. A bit more snooping resulted in figuring out that the 4-6 pins group was grounding. This snooping was to simply check which wire goes where, on a Molex to SATA power connector adapter, but that's beside the point.


(Click on the images to view them in full size)

The above images are from the internal side of the hard drive’s printed circuit board (PCB). The image on the left shows the two connectors: the Data (on the left, the smaller one) and the Power (on the right, the larger one), with the red arrow indicating the fourth pin matching the missing one from the motherboard.

The key to solving this fix is the image on the right
. Notice that the pin group 4-6 (highlighted in the red circle) is interconnected. All three pins are short circuited via the PCB wiring, which means they all function as one pin, as mentioned earlier. As this is in the Power group of pins, and on top of that, pins 4-6 are grounding, there will be no problem to simply ignore the missing pin 4, as pins 5 and 6 will do a sufficient job of grounding. So the fix then is only to glue the broken plastic wrapping, as mentioned previously, and that is it.
For over a month now, the HP 6710s works flawlessly, and I’m actually typing this text on it. The repair for the SATA socket took less than 10 minutes, and that got me a perfectly working laptop for a bargain price.


If you find my blog posts helpful please consider a small donation.




Let your friends know about this blog post
Share/Bookmark




Tuesday, March 03, 2009

Fixing a non-responsive HP nx6110/6xxx series laptop

The HP nx6110 is a great laptop but this product has one major fault: after a while, it starts to freeze up randomly. This problem has to do with the FSB chip which controls the mouse, keyboard and storage devices on the HP nx6110. To put it more simply, it is the part of the chipset controlling your peripherals, and with this defect, the HP nx6110 freezes up randomly and in some extreme cases cannot move beyond the bios HP logo.

Here are some of the usual symptoms:
  • HP nx6110 is stuck on the HP logo
  • HP nx6110 does not boot
  • Mouse pointer freezes up randomly on HP nx6110
  • Keyboard does not work on a HP nx6110 laptop
  • DVD does not work or is slow
  • HP nx6110 freezes up when moved
Here's what causes this problem:
Due to a mounting restrains caused by the hazardous materials policy, this chip suffers
from what is called “a chip creep” effect. As the name suggests, the chip “takes a walk” and some of its hundreds of ball-shaped pins looses contact with the motherboard. This causes the PC to freeze-up randomly, or when moved around.

Here's how you can fix your non responsive HP nx6110 laptop
Forget about taking your laptop to repair centers. They'll convince you that you must buy a new motherboard which will cost you over $250 with the installation fee.
The simple trick is forcing the FSB chip to reestablish connection between the GPA (grid point array of the FSB chip) and the motherboard.
Even though this repair process sounds simple, it's not. Imagine you have a small 1x1inch box with over 400 pins, and each needs to touch the motherboard. If you push too hard on one end, you'll cause the pins on the opposite side to lose contact. If you press to hard on the entire chip, you can cause the pins to break. Some people while trying to minimize costs of repair, have tried to figure things out only to get the motherboard to being unrepairable. My experience and suggestion is to always play it safe if there is such a way. Here, you can get the HP nx 6110 laptop repair tutorial and if you follow the instructions it will greatly improve your chances of repairing your laptop. Please don't attempt to improvise as you may cause more harm than good. Just get the tutorial and use the chance you have to save your laptop. Too many attempts can only make your laptop irreparable.



Let your friends know about this blog post
Share/Bookmark




Thursday, January 22, 2009

Maxim1532a - Maxim1987 issue on Toshiba M35 Motherboards

My fix for the non-responsive Toshiba M35 continues to produce happy readers. I'm glad for that.
This morning I got a question:

I had reassemble my m35x-s329 and found that the power chip using Maxim-max1532a ETL instead of max1987. Can I just replace by max1987 which is easier to found this specific on the market..

ID motherboard K000019630.

Unfortunately for all of us Maxim/Dallas Semiconductor left us out in the dark on their MAX1987 power driver chip, so we can only derive conclusions of its functionality/characteristics. On the other hand, there is sufficient info on the MAX1532a, and as I understood the document, it is a power driver, used on P4 and P4 Mobile CPUs, produced sometime 2003, provides 1, 1.2, 3.3, 5V, and also has "high voltage" module for the more demanding components. WOW. That is something we didn't really know. Thanks Maxim/Dallas. In my search for more info, i also found one document that mentions both the Max1532 and the Max1987. But that's basically all it does. It mentions them.

So, let's get back to the initial question: Can the Maxim1532 be used instead the Maxim1987?
The logic may suggest that these two bunnies are interchangeable. But that's only guesswork, a hunt in the dark. The input and output voltages are the same: you get the same 18V DC, same battery, same (?) CPU, RAM, Chipset etc. so judging by the "black box" approach, if the same stuff enters both black boxes, and the same stuff comes out on the other end of both boxes, chanses are the black boxes are identical. For an old laptop, I'd say heck, try it! If it burns, it wont be a big deal as its a cheap thing anyways. But I'd not do it if it was used in a pacemaker, so I offer no warranties on this advice.
If you DO however choose to test the compatibility the hard way, I suggest removing the modem board, RAM, CPU, HDD, DVD... anything that is removable, so if things to get hot, you wouldn't waste the peripherals and the CPU/RAM. Attach only the switch board and the CPU fan, to get a feedback if it spins up. Then, plug in the CPU and try again. If it works, great. If not... no big loss as you already had a malfunctioning power driver.
In case if you want to purchase it, I found this site where you can order it.
Whatever happens, let the community know.
Thanks again to all of you who read, fix and share experiences. By the way, if you do visit this blog often, scribble a note on the other posts as well, just to know that somebody out there other than Google sees my stuff.

If you find my blog posts helpful please consider a small donation.




Let your friends know about this blog post
Share/Bookmark




Friday, January 09, 2009

RoHS is guilty for the Toshiba M35X and HP NC6000 laptop dead motherboard


Due to a surprising popularity of my text on fixing a Toshiba M35x motherboard problem, I decided to update you all on the situation with the laptop and some other points brought up by folks who used my tutorial.
In the past several months I received many “thank you” posts, and I’ve also received some comments that prompted me to update the previous post with some extra info.
First of all, I’d like to thank everybody who publicized my fix on other websites. Some of them properly quoted my text and passed credits to me, while others unfortunately did not have the courtesy to mention that http://imateski.blogspot.com is not their blog. Sad, it’s their loss of integrity. I’ve also learned that Toshiba has some problems with law suits over the M35 series which means this is a major deal… folks suing the company because it produced a bad product. I’d rather sue them because their support technicians are too lazy to work at problems and figure out how to justify their high salaries… but that’s what I’d do. Apparently Toshiba thinks it’s better to pay fines instead of hiring some competent folks… like me for example :)
Further on, I want to thank folks who commented with constructive questions and comments which prompted me to do some search to see where my text is mentioned, and to my surprise, one of the comments on my blog pointed to an ebay, and I also found a pirated copy on Scribd. Good thing Scribd has a good Copyright response team, which took about a day to address the issue.

Now, about the updates…
First, one of the comments pointed out that the same fix worked for HP NC6000 and NC 8000 laptops also. While searching through other sites, people report of using the same fix on Toshiba Satellite A70, m115, and alike. I've also found out that some people used this tutorial to repair Gateway laptops. I guess the tutorial in general works on any laptop produced after 2000.
The second thing I’d like to share is a bit of theory behind this problem.
As we all know, the world is moving toward green technologies, and one of them is the enforcement of the RoHS certificate, which basically means Restricition of Hazardous Substances. For electronics, this means no Lead in the solder alloys, which means no flexibility for the solder joints. For some chips, this is a good thing, but for the Maxim chip design, its not so good. For general understanding of how RoHS and lead-free alloys affect the electronics industry read up on Wikipedia’s article. It’s quite good. For a more scientific explanation of the effects of Lead-free alloys on chip-PCB contact tensions, read this article. To summarize them both, the failure of the Toshiba Satellite M35 and Satellite A70 series, as well as HP NC6000 /8000 is due to large surface tensions between the chip and the motherboard. Due to poor elasticity of lead-free soldering alloys, the solder joints crack and slowly oxidation builds up which leads to electronics failure. This is why I suggested using a hot air gun for resoldering the Maxim chip, but unfortunately none of the electronics service shops wanted to play with the motherboard. Resoldering with a plain solder iron can only mend the problem, it cannot fix it permanently. I just had the Toshiba M35 in for repair again, probably due to lead-free residues between the motherboard and the MAXIM pins. If it were totally removed, both the chip and the PCB could be cleaned off from the lead free alloy, and resoldered back with the plain elastic Pb60Sn40 solder alloy (60% Lead, 40% tin). Alas, we do what we can with the resources we have. I resoldered the chip again, and sent it back, free of charge. Heck, it only takes about 30 minutes of work.
And one last thing, just for the fun of it, here are two links to images that illustrate the problem with pins not covered with solder alloy, found in the Wikipedia article, and here is a photo of how the solder looks with Lead free, and normal solder alloys.
Jesus is coming, be prepared.

If you find my blog posts helpful please consider a small donation.




Let your friends know about this blog post
Share/Bookmark


Saturday, August 23, 2008

Dell Inspiron 9100 thurough cleanup

In this text I will explain the process of opening up the computer so that the CPU cooler and radiator can be cleaned up.
This machine heats up like crazy. It is an impressive piece of equipment in all aspects. Its owner, Marcel, got it a five years ago, and he had quite an experience with it.
Two years after the purchase, its hard drive died. Then, a year after, the replacement disk also died. And finally, Marcel came to me with his laptop and asked for help. Of course, he still had to buy a new hard drive, third in a row.
The reason for the hard drive failures was the clogged up cooling system, which is impressive, as everything else on this machine. It has two big ventilators accessible from the bottom of the laptop. They are located on the corners beneath the LCD. Both can be removed by removing a total of 4 screws. There is another, internal ventilator which is the primary one.
The cooling system of this Dell is made in a cascade style. The internal ventilator cools the CPU, while the other two deal with the rest of the CPU heat (on the upper right side) and the Graphics card (on the upper left side). This is why all three ventilators/radiators must be cleaned up in order to insure good ventilation and to prevent hardware failures.
The picture below is from the central ventilator/radiator assembly (note that the metal shielding of the radiator is removed)

The biggest challenge is to get to the central radiator simply because you have to open up the laptop from the top side. Once you remove all the plastics and get full access to the motherboard, you will see a metal plate that is wrapped over the primary CPU radiator. To remove this cover, get a sharp screwdriver or a small knife to access the locks on its sides. It is a simple removal, but you need the tools for it.


Here is a close-up of the locking mechanism for the cover of the CPU radiator. There are four of these locks, on each corner.


Once this cover is removed, you have clear access to the ribs of the radiator, and all you need to do is to simply remove the dirt with hand or with a small brush.
Below is a photo of the motherboard with labeled airflows (thick arrows 1 and 2) and in the red elypses are the key details for each ventilator/radiator assembly (note that the ventilators are removed).


There are plenty of connectors in this machine, so you must make sure you plug in all of them firmly into their slots. The detail on the photo below is the cable from the LCD. If you do not firmly place it in its slot you may get problems with the LCD.


After cleaning up the laptop thoroughly it worked fine. It still is hot due to its processor, but the hard drive has been working for about two years now without any physical deterioration (according to the SMART parameters).
The lesson to take home from this post is that laptops need to be cleaned up at least once a year, depending on the environment you work on. It is even worth paying a PC technician to do the job for you. It will be cheaper and less stressful for you to pay a fee for cleaning up the laptop instead of losing time and money, as Marcel did by buying 2 extra hard drives.
Hope this helps. Let me know if it did and in what way.

If you find my blog posts helpful please consider a small donation.




Let your friends know about this blog post
Share/Bookmark


Dell Inspiron 9100 wont turn on

This text explains the repair of a dead Dell Inspiron 9100. The laptop did not turn on at all. One day it works perfectly, and the next - nothing.
There are more reasons for this kind of failure, and you can find plenty of it online. The best way to go about this problem is to first remove the ram chip(s) and try boot. If it boots, or gives the beeps for a missing ram, then you probably solved the problem - it is bad ram chips, or poor contact between the slot and the ram board. In this particular case both ram boards were OK, but one of them did not work on its original slot, so I swapped them. When I thought the problem is solved by swapping the slots, the computer did not boot again. Then I took out the suspicious ram chip and inspected the pins. I realized that it had a layer of corrosion on some of the pins, so I took nail polish remover and wiped thoroughly the contacts with a fine cloth. This corrosion probably happened due to poor handling of somebody who installed the ram. Probably the person touched the contacts with sweaty fingers or something, and time did the rest. After wiping the contacts I placed the ram back in the slot, and added some paper between the chips and the ram cover, so that it would force the ram chips firmly in the slots and insure good contact. That fixed the problem and I had the computer on for more than 30 hours to make sure that it will work. Now its back to its owner who is happy that he has his computer back without any big investments.

If you find my blog posts helpful please consider a small donation.




Let your friends know about this blog post
Share/Bookmark


Wednesday, August 20, 2008

Toshiba Satellite m35x motherboard repair

Wednesday, March 23, 2011
After three years of publishing this manual, I just did the Third Edition of this ebook and added a ton of new materials. With over 30.000 happy people that repaired their laptops using this manual, I'm happy to present this Third Edition with all the updates, suggestions and answered questions that people sent me in the past year. It is as people say, "a great book with very clear explanations" and I believe this will help you to repair your laptop as well.


If you own a Toshiba m35 or HP laptop that does not turn on, chances are your laptop is one of the hundreds suffering from the Maxim chip failure. I faced that same problem two years ago. But don't worry, I fixed my Toshiba m35 and you can too. 
But before we move on to the repair tip, see if your laptop has some of these symptoms:
  • Does your laptop fail to turn on any time you press the power button?
  • Do the LEDs blink for a seconds and then shut off and the laptop shows no signs of life?
  • Does the CPU fan spin up for a second and then the laptop goes dead again?

If your answer was YES to at least ONE of these questions, there's a 90% chance you're on the right place. If you answered YES on two questions, you're about to find out how to fix your laptop in less than an hour.




This repair manual has:

  • 28 pages of great explanations of the defect and repair
  • 12 images and illustrations so you can clearly see what the problem is, and how to fix it
  • 3 repair scenarios so you can pick the one that matches your level of technical know-how
  • 4 illustrations explaining the safest repair process
  • 3 videos explaining the easier but more advanced approach
  • an Appendix section explaining how to do a high quality resolder of the power plug
  • a dissasembly instructions list with links to the Toshiba and HP service manuals



Did you know that Toshiba and HP together spent millions in repair fees over this same problem? Toshiba had problems with their M-series (especially m35, m115, then A65, A75 etc)  produced between 2002 and 2008, and HP had problems with the NC series, especially nc6000, nc8000 and nc9000 models. If you go to their repair centers, you’re likely to end up with a new motherboard and a repair fee of at least $300 for the motherboard and labor. This repair process lasts for over 10 days if you get lucky, and there is no guarantee that they'll manage to find a suitable motherboard as production stopped a few years ago.

If you spent some time researching this problem you probably found many so called repair tutorials that ask of you to figure out the binary code of the LED blinks, and then they ask you to post that code only to get a response such as

"You have a problem with the 3.3V module"
or 
“Your motherboard reports an A2H fault, you’ll need to consult the repair handbook for that.” or 
"You'll need to repair the power regulating circuitry"

The bottom line is that all these error codes point to the power module which is integrated in the Maxim 1987 (Maxim 1532 in some models). Repairing the power module doesn't take much time, but it does take some guidance. The trick is in a redistributive resolder of the Maxim 1987 chip. If you've done redistributive re-soldering you are set to go. The trick is not to use heat gun to do a simple "reflow" because this is just a temporary solution. Of course, there are plenty of people that advocate reflowing, but if you dig deeper into the dry solder issues after the RoHS legislative (that banned Led-based solder alloys) you'll realize just as I did that the only way to make your Toshiba or HP work again is to use the redistributive resoldering technique.

If you never heard of redistributive resoldering I strongly suggest that you don't try to look for repair shortcuts and by no means use a DIY approach. If you are not a seasoned Surface Mount Device-level repair technician you'll need technical guidance. I have a step by step repair manual that will help you understand the problem, and teach you how to perform this redistributive resolder of the Maxim chip

Here's what you get in the PDF illustrated repair manual:
  • Step by step dissasembly instructions, 
  • Maxim 1987 power driver resolder instructions,
  • Power plug resolder instructions.
  • illustrations and videos to guide you through the repair

Tuesday, February 26, 2008

Black Hole WD

These are some of the photos of a dead WD500AAKS, that took with it 450GB of stuff, and years of research on a PhD level. I attempted to swap the heads and PCB from a WD500AACS. The reason for this opinion is an information from a tutorial at hddguru.com. The tutorial stated that the fifth and sixth characters in the DCM code should be the same, and if they are, then the two hard drives use compatible heads. Well, after opening the brand new WD500AACS, I saw that it has two platers while the AAKS had three. This meant that I just messed up a new HD because when I returned the PCB and closed up the new HD, it did not work anymore. It actually behaved the same way as the old HD behaved. Anyways, here are the pictures.


If you find my blog posts helpful please consider a small donation.




Let your friends know about this blog post
Share/Bookmark


Sunday, January 13, 2008

Hard drive failure

This summer, when we went to my father and mother in law, I decided to format my HD, reinstall everything and make an image of the freshly installed and tweaked system. On my late Toshiba Satellite M35x, this took about five hours. With the amount of experiments I do, it is not logical to waste so much time every time I mess up beyond repair, so I decided to immediately put the image of the HD on a DVD. So, I took out the 9 months old Samsung 80GB, 5400rpm HD on my wife's desktop and finish the work. I set it up, started Norton Ghost and in less than half an hour, the image was on my wife's computer. Then I went crazy. I decided to take an old Toshiba HD that a professor of mine gave it to me as a "payment" for an operation I performed on his Dell laptop, and see how it would perform. Now this HD was in a poor shape. Due to the Dell's clogged cooling system it got cooked in only a few months and developed a ton of bad sectors. So, I used WD Diagnostics, a free but very efficient tool to mark out the bad sectors, and then the Toshiba HD did work fine. I placed the image installation onto the Toshiba HD, mounted it in my laptop and booted up. Everything worked fine. Then I decided to play around with the disks. I put the Samsung in a 2.5' USB tray and plugged it in my wife's computer, and noticed a small spark when I touched the USB cable to the HDD. Then when I tried to plug it on my laptop, all I heard was NOTHING. So, I pluged it back on my wife's comp. without any sucess. I could not believe that I just destroyed my hard drive and all the papers with it. So, I figured, I have the warranty, I can take it to the store and get a new one, but that would mean that I will never see my documents again. I also thought that I am not ready to pay ridiculous amounts of money so that a guy just like me would retrieve the data in the same way I would. So, I decided to forget about the warranty and go ahead and play with the drive. I figured, the only thing I would lose in a worst case scenario is the $120 I paid for the drive. Paying for data retrieval was out of the question. So, I opened the dead HD with the intention of moving the plates to another HD who had good mechanics. I know that this has practically no chance of working... but hey, I had nothing to lose (not any more), and I was dead board without an internet connection.
Now, knowing that the read/write heads are not supposed to touch the plates, and the only thing that keeps them floating is the air flow created by the rotation of the plates (just like airplanes fly), I was surprised and relieved to see this situation, presented on the photo:


As you can see, the r/w heads are not where they are supposed to be. The very fact that the plates are not spinning and the heads have landed on the plates is a clear sign that this HD will definitely die very soon. As I read online, the sensitivity of the heads and plates, a potential physical contact on a microstructural level would do damage that is equivalent if you take a 12 story building and drag it along an asphalt road. It will destroy both the road and the building. So, that meant that I have a somewhat destroyed r/w heads, micro chips that have teared off the heads and plates... and the worst of enemies - dust particles. My bedroom is no "clean room" so there is definitely more than 100 dust particles on a cubic meter. There are millions, and not so small particles either. Anyways, as things are, the disk is ready for burial. So another scratch or two wont do any crutial difference. So, I slided the heads off the plates onto their resting place. The next photo is to illustrate where the heads should be (this is actually a different HD, but you get the idea of where the heads should be positioned when the HD is turned off):


After sliding the heads off the plates, I closed up the HD, plugged it back on the USB tray, the computer recognized it fine, and I started copying the data. The copying lasted for about 10 minutes and then errors started appearing. They got so bad that a normal copying did not do the job any more. So I used WinHex to copy the last few documents. They were a bit damaged, but WinHex helped in editing them so the entire process finished with 100% successful retrieval of all my data. The only loss was the actual hard drive... which in the long run did not mean so much because I had the old Toshiba HD that worked... and a couple of months after this event the laptop itself died. But that is another story.
What we all should learn is that USB hard drives are very much different from memory sticks. The disks have moving parts and they have to go through a procedure for removal, so always do the "Safely remove hardware" in order that the HD may safely shut down. Next, have a good grounding of the desktop, because you may end up with a fried component because of the poor grounding. The third and most important lesson is that you must always, always, under any circumstance, have a second computer, 2.5-3.5' adapter, torx screwdrivers, good forensics software and crazy enough mind to open the HD when it refuses obedience.

If you find my blog posts helpful please consider a small donation.




Let your friends know about this blog post
Share/Bookmark


LCD suddenly died

Well, bears go to sleep in winters, but according to my blog activity, what we can know for certain is that I am not a bear. Let this ruminate in your mind for a while.
The fix that I will explain is for a Fujitsu Siemens laptop, not so new one... a PIII 1GHz, who's LCD suddenly went dark. The laptop did turn on, I could hear all the expected spinups, LED blinks, and managed to log on and hear the HD work... but no picture. I plugged in an external monitor and got the desktop. Diagnosis: there's something wrong with the LCD. There are usually two things that usually go wrong: a broken back light, or a broken inverter. The illumination of the LCD is similar to the fluorescent or "neon" lights as we call them in Europe. There is one very thin and very fragile fluorescent light usually mounted on the top of the LCD, and a "starter circuit" called an inverter. This inverter uses 12V and through some active electronics creates high voltage with low amperage that ionizes the neon and lights up the fluorescent lamp.
I had a similar problem some years back with a Compaq Armada M700. Then I opted out for a new inverter. That fix was $50, the price I paid for a second hand inverter. The Armada works perfectly fine till this day.
With the Siemens I had on my desk I could not immediately go for a new inverter because the owner was a poor student, so opting for a $50 solution was not really a solution for him.
So, I pulled out my UNI-meter, and started testing for current activity in the inverter circuit. The inverter boards are neatly divided in a low-voltage and a high-voltage part. The low voltage is on the side where the cable from the motherboard is connected to the inverter. This cable has at least 4 wires. The high voltage part is the one from which a two-wire plug gives out high voltage to the bulb. I started testing the low voltage segment. I found no activity, so I started testing the diodes and capacitors as the most probable causes for a malfunction. As I worked my way through the SMD's I ended up at the fuse, and to my surprise, that was busted. It turned out that the simplest of solutions was actually THE solution. The orange cube in the bottom left part of the photo is the busted fuse. It is a 1.6A fuse.
After finding the broken component, now I had to replace it. Since I am a student too and do not have a full size workshop with all the components I would ever need, and I had to keep the expenses for repair to a minimum (meaning no expenses at all), I decided to find an appropriately thin wire and bypass the busted fuse. You can see the wire going from the left of the fuse all the way to the right... it looks like a silver arch resting on the printer board. This is a very very thin wire, the thinest I could find in my room. I had to make sure that the wire both bypasses the fuse, and is just the right size so that it would not break when the LCD is on, and at the same time not too thick so that if the circuit overloads the wire would be the first thing to break. The fuse itself looks quite big on the photo, but its actual size is about 5mm length, so it was a tedious job to solder the piece of wire. For an old laptop, fixing the inverter is probably the best option since its market value is not much higher than what he would pay for a new inverter.

If you find my blog posts helpful please consider a small donation.




Let your friends know about this blog post
Share/Bookmark